CAD/CAM Implant Restorations In-House: Should I Head in this Direction?

Dr. V. asks:
I have been doing CAD/CAM restorations on natural teeth for 2-years and been very happy with the results. This saves a visit for the patients and saves me the trouble of making a temporary crown or onlay. I place my own implants and have just started doing immediate placement and immediate temporization. I am thinking now that maybe I could do the permanent restoration with CAD/CAM in-house. I have not done this before and I just want to run this by the experts out there. After the osseointegration is complete and the tissues have healed, I plan to remove the temporary crown, scan the abutment and make a CAD/CAM crown. My only concern is tissue management. For subgingival margins, how do I best retract the tissue so that I can ge a clear scan of the finish lines?

11 Comments on CAD/CAM Implant Restorations In-House: Should I Head in this Direction?

New comments are currently closed for this post.
Bruce Cassis
9/29/2009
Properly utilized, lasers provide an environment for immediate CAD/CAM impressions.
Chris Winterholler
9/29/2009
I have done hundreds of these restorations with CEREC starting as far back as 2001. There are certain implant systems that are more ideal for this method than others and it all has to do with the design of the shoulder. THe new emax blocks from Ivoclar are the perfect material for this technique. I recommend that you impress with impergum the immediately placed implant with a transfer assembly, then make a quick model with snap stone, do your gingivectomy on the stone model and then design from the analog. THis makes your gingival colar in the mouth undamaged and able to contour with a diode laser if necessary. I also recommend drawing the margins on your CEREC design on the tissue for the proposal and then edit the line after the crown is proposed and right before you mill. This will make your proposed tooth from dental data base one that fits in the arch and maximizes the esthetic and functional potential of the crown. Good luck, CAD/CAM and Implants are the perfect marriage....
Andri Suwardi
10/2/2009
I have done a video, the topic was " Immediate 3D Cad/Cam Restoration in Implant Dentistry ". I am using laser ( waterlase ) for tissue management before scanning the abutment implant. If you would like to see the video, you can download in my website ( www.andrisuwardi.com ) pasword : isid2009
Cliff Leachman
10/6/2009
I agree with Chris! Take an implant level impression and work off models with a bite record. If your using Cerec I personally don't think its a good idea to spray Titanium Dioxide powder into your site or the mouth or lungs at all for that matter. I just cemented an e.max A1 LT block on a first molar ~ hour ago and the results were excellent. The cost savings and esthetics of using a porcelain block on a titanium abutment are significant and with the NEW Ivoclar all-purpose silanating agent and implant cement you have the perfect combination. I used to think that excellent ceramic temporaries would be the only use for my D4D, but I now have, happily, moved into the permanent realm.
mike stanley, asst.
10/7/2009
new research is showing e.max to be stronger than PFM because it contains fewer internal defects. we've done a dozen or so...
David Hubbell
10/7/2009
I have done a bunch of these too. If you are working subgingival, I always use an impression cap and work from an analog. I think the most popular opinion is that all porcelain crowns are not strong enough to work on implants. Thus, the use of e-max is recommended by most people. (Chris' response) I think that is good advice. My thinking is, even if you have a metal or zirconia core in the crown, they still have to stack porcelain over it. The core will never break but the porcelain can. I think this is true no matter what you use. E-max is very strong for the whole crown. I think ---- so what? If my crown breaks maybe that is a good thing. I certainly don't want the bone, the fixture, the abutment or the screw to break on the implant. If the crown breaks I have it stored in my CEREC machine and I can mill a new one and have it ready before the patient gets there. It is a 15 min. appointment to change one. I have had this happen 1 time out of a hundred or so that I have restored this way. My patient bit down on a rock in some re-fried beans and broke the crown. That would probably break anything. With milled crowns the margins are great and they seem strong enough especially for bicuspids and anteriors. I think they are all good solutions. Work indirect for deep margins and do it. I prefer Vita or LT empress CAD to block out the metal color. Have a selection of opaque composite cements to bond with. I like to scuff up the metal abutments some with a fine diamond before I cement. That seems to help with the stability of the cementation. This is just however, my clinical experience and hasn't been researched. Good luck. Have fun. I think they work great.
R. Stanton
10/7/2009
A PFM has 1000Mpa strength core under 100Mpa strength porcelain so when it breaks, WHAT breaks? Always the porcelain, never the core. eMax approaches 400Mpa for the WHOLE restoration so it is overall a superior choice. I use it to restore all my implants. I usually work off an analog model but occasionally scan the abutment and bite reg. in the mouth if I feel I need to for various reasons.
Farzad Setayesh
11/26/2009
I want to buy CEREC3 and use it for implant. Is it any problem by ceramic restoration color and titanium abutment by CEREC?
Larry J. Meyer
11/26/2009
I agree with the above posts. I use e-max cad and have been very happy with the results. I always work off a model now with the analog and final abutment. If necessary I have a custom abutment made. The metal show through isn't a problem when using the LT blocks at least so far, unless the procelain is thin as in the gingival margin area. If necessary we can prep the abutment to get a deeper margin for thicker porcelain. It saves a ton of money comppared to lab costs and is fun. Every time I can use my CEREC I do so and now with the Cerec Direct we can even scan, e-mail, and have the labs make bridges. Larry J. Meyer
Farzad Setayesh
12/18/2009
If I have AC Unit in office and CEREC IN LAB in there can I make a frame with camera and without impression?
Dr Dean Vafiadis
11/27/2010
For those who are already restoring implants with CAD/CAM technology you see the results and they are favorable. 2 things to consider: First, permanent cement or provisional cement. We are gathering data on this. No papers published to date. It really depends on the type of implant system you are using and wether the screw is likely to get loose. As you can imagine to try to cut off an emax to get to a screw could be a bad day!!! Second, is the occlusion issue, and is is this material so strong that it may damage opposing natural teeth if we don't pay attention to our occlusion. Also, what kind of occlusion scheme should we use. Should it be "light" contact.. then we must define "light" how light or how not so light.. should there be some contact and how strong is the contact. Something like TEKSCAN, may have it's place here. For those who are thinking about cad/cam impressions or cad/cam in-office fabrication..it seems this has become standard protocol for our prosthodontic office. we use the Cerec 3d Blue cam. I believe this will be the future of fabricating implant restorations!!!

Featured Products

OsteoGen Bone Grafting Plug
Combines bone graft with a collagen plug to yield the easiest and most affordable way to clinically deliver bone graft for socket preservation.
CevOss Bovine Bone Graft
Make the switch to a better xenograft! High volume of interconnected pores promotes new bone. Substantially equivalent to BioOss and NuOss.